How To Get Best Results From Your Perfection Heater
1.Keep the perforations in the gallery open.Keep the perforations in the gallery free from
lint and dirt by wiping gallery every day or two. If any of the perforations become clogged, the air
supply is reduced, causing the heater to smoke.
2.Keep the flame spreader clean.With a stiff brush, clean all perforations and with a knife
scrape the carbon off the flange against which the wick strikes.Hold the flame spreader to the
light to see that all perforations are clean and open.
3.Keep wick tubes clean.Keep the char cleaned from the top of the wick tube by wiping with
a cloth.
4.Clean wick daily.If the heater is in daily use, clean the wick daily. Remove the flame spreader
and raise the wick until the top portion is even with the top of the tube. Wipe loose carbon or char
off the top of the wick with a cloth. Pat the remaining wick down evenly with the fingers.
Do not allow reservoir to burn dry.Each time this happens, one-quarter inch of the wick is
consumed.
5.Burn heater at high flame.This heater is built to burn at high flame and will not smoke if pure
kerosene is used and the wick, gallery and flame spreader are clean. Simply turn wick up as far
as it will go. Apply match to SIDE of wick and close heater. (Never lift the flame spreader to light
top of wick.)
6.Supply plenty of fresh air.Perfection heaters burn many hundreds of gallons of air to each
gallon of kerosene. When used in a bathroom or other small space, leave the door ajar two inches
so that fresh air can flow in. It will be warmed as it passes up through the heater.Insufficient
supply of fresh air will cause the heater to smoke.
7.Use pure kerosene.Use only a good grade of kerosene.Never mix gasoline, even a small
amount, with kerosene. It is desirable to drain the reservoir occasionally and then put in fresh
kerosene. This will safeguard the reservoir and wick carrier from possible corrosion and rust by
eliminating any moisture that may have accumulated by condensation.
CAUTION: If used on a trailer, boat or other moving conveyance - NEVER operate this
heater while in motion. A serious fire may result.
SPECIAL DIRECTIONS BEFORE LIGHTING HEATER FOR THE FIRST TIME
Parts of this heater have been oiled to prevent rusting. Before lighting heater for the FIRST TIME,
wipe thoroughly with a cloth. Since the remaining oil will burn off, causing a disagreeable odor for ten or
fifteen minutes, the heater should be placed where this odor will not be offensive.
To Insert New Wick
When that portion of the wick that projects above the metal wick carrier has been burned away in use and
the wick refuses to turn up any further, remove it and insert a new wick.
1.Remove Flame Spreader.
2.Remove Gallery by turning counter clockwise.
3.Turn wick up as high as it will go, with adjusting wheel.
4.Pull out both the used wick and metal carrier from the wick tube and throw them away.
5.Remove new wick from carton, straighten out folded-in ends, and remove stiffener from inside of
wick.
6.Place wick, split end down, over the wick tube. See that split side of wick straddles the two cog-
wheels that operate wick carrier. Force wick down until cog-wheels engage with holes in metal
wick carrier. (Should the wick catch while forcing carrier down, it is due to the small points at top
of wick carrier catching over the wick tube.Apply pressure on carrier so as to release these
points.)
7.Turn wick down as far as it will go by means of adjusting wheel.
8.Replace gallery by turning clockwise as far as possible. Be sure that the threads on bottom of the
gallery squarely engage threads on reservoir.
9.Turn the wick up level with the top of the wick tube. (If uneven, level it by pulling up the low side
of the wick.) Clip any loose threads or ravelings projecting from the top of wick with scissors.
10.Replace flame spreader. Fill reservoir with kerosene and allow the wick to soak at least a half hour
before lighting to allow the wick sufficient time to completely absorb fuel.
To Fill Reservoir
Tilt upper drum back and remove reservoir.Lift up fuller cap and fill the reservoir with a good
grade of kerosene.If the reservoir is full the rod in the center of the filler cap will be raised about two
inches above the filler cap.This rod, which is part of the built-in fuel gauge will return to its original
position as the kerosene is used up. Replace reservoir in heater.
To Light Burner
1.With wick turned down, first make sure that flame spreader is secure in its position on top of wick
tube and that gallery is screwed down tight.
2.After giving wick time to become saturated with kerosene, using hand-wheel, turn wick up until
flame spreader stops it.
3.Apply lighted match to SIDE of wick in several places.
4.Close heater and make sure that catch is securely fastened.The safety catch should be locked
under the lowest lug. If heater has a spring catch, make sure that it snaps into the closed position.
To Extinguish Flame
Turn wick down as far as it will go. This will permit flame spreader to drop on top of wick tubes
and extinguish flame.
Storage Precautions
When heater is not to be used for a month or longer, empty reservoir and store heater in a dry
place: an empty reservoir virtually eliminates condensation. If there is danger of rust, steel drums
should be protected with oil.